Updated November 2026

Replacing a worn or broken part on an electric bike is often cheaper and faster than replacing the whole system, but only if you buy the right component for your controller, display and brake setup. This guide compares five replacement parts of electric bike systems that riders commonly search for, focusing on voltage compatibility, connector type, cable length and how well each part is described for typical e-bike and e-scooter setups.

Our top picks at a glance

  1. 1LCD 5-Pin Electric Bike DisplayTOP CHOICEBest overallLCD 5-Pin Electric Bike DisplayView on Amazon
  2. 2Brake Lever Handle Bar Grips 2-Wire PairTOP CHOICEBest for brake lever replacementBrake Lever Handle Bar Grips 2-Wire PairView on Amazon
  3. 32-Wire Electronic Brake Lever PairTOP CHOICEBest for electronic brake upgrades2-Wire Electronic Brake Lever PairView on Amazon
  4. 4E-Bike Connection 1T4 Extension CableBest for extra cable reachE-Bike Connection 1T4 Extension CableView on Amazon
  5. 5S866 Electric Bicycle LCD Display MeterBest for a budget display swapS866 Electric Bicycle LCD Display MeterView on Amazon

Our Top Picks

Product Best for Key feature
LCD 5-Pin Electric Bike Display Full display replacement 24V–60V range
Brake Lever Handle Bar Grips 2-Wire Pair Basic brake lever swap 12 cm cable length
2-Wire Electronic Brake Lever Pair Electronic brake upgrades Waterproof 2-pin design
E-Bike Connection 1T4 Extension Cable Reaching a distant component 105 cm cable run
S866 Electric Bicycle LCD Display Meter Budget display replacement 24V–48V with odometer

LCD 5-Pin Electric Bike Display

LCD 5‑Pin Electric Bike Display,Cycling Computer Screen Replacement Parts,24V‑60V Ebike Display Control Panel for 22.2 Handlebar E‑Bike Scooter

LCD 5‑Pin Electric Bike Display,Cycling Computer Screen Replacement Parts,24V‑60V Ebike Display Control Panel for 22.2 Handlebar E‑Bike Scooter

View on Amazon

Best for: Full display replacement

This suits riders whose screen has failed or who want a display that matches a 22.2 mm handlebar and a 24V–60V system.

Pros

  • Wide voltage range listed by the manufacturer
  • Five-pin connector for common e-bike setups

Cons

  • Compatibility depends on matching your controller’s pinout

View on Amazon

Brake Lever Handle Bar Grips 2-Wire Pair

Brake Lever Handle Bar Grips, 2 Wires Left & Right, E-Bike Replacement Parts 2 Pin Brake Levers for Electric Bicycle, 12cm Cable Length, 1 Pair

Brake Lever Handle Bar Grips, 2 Wires Left & Right, E-Bike Replacement Parts 2 Pin Brake Levers for Electric Bicycle, 12cm Cable Length, 1 Pair

View on Amazon

Best for: Basic brake lever swap

A practical choice for riders who need a left and right lever set with a reasonable 12 cm cable run.

Pros

  • Left and right pair sold together
  • Listed cable length suits most handlebar layouts

Cons

  • Confirm the two-pin plug matches your brake sensor before ordering

View on Amazon

2-Wire Electronic Brake Lever Pair

2-wire connector left and right electronic brake levers for electric bicycles scooters 1 pair Durable Waterproof 2-Pin Electronic Brake Lever Pair for E-Bike Scooter

2-wire connector left and right electronic brake levers for electric bicycles scooters 1 pair Durable Waterproof 2-Pin Electronic Brake Lever Pair for E-Bike Scooter

View on Amazon

Best for: Electronic brake upgrades

Fits riders replacing electronic cut-off levers on e-bikes and e-scooters that use a two-pin signal.

Pros

  • Waterproof housing described by the seller
  • Sold as a left and right pair

Cons

  • Check that the signal type matches your motor controller

View on Amazon

E-Bike Connection 1T4 Extension Cable

E-Bike Connection 1T4 Extension Cable 105 cm E-Bike Gas Brake Display Accessories for Electric Bicycles

E-Bike Connection 1T4 Extension Cable 105 cm E-Bike Gas Brake Display Accessories for Electric Bicycles

View on Amazon

Best for: Extra cable reach

Useful when a display or brake sensor sits too far from the controller and the original harness is a few centimeters short.

Pros

  • 105 cm length gives room to route cables along the frame
  • Works as an accessory rather than a full replacement

Cons

  • Extra connectors add points where water or dirt can enter

View on Amazon

S866 Electric Bicycle LCD Display Meter

S866 Electric Bicycle LCD Display Meter, 24V 36V 48V Ebike LCD Display Control Panel Wireless Bicycle Speedometer Odometer for Electric Scooter Electric Bike Modification

S866 Electric Bicycle LCD Display Meter, 24V 36V 48V Ebike LCD Display Control Panel Wireless Bicycle Speedometer Odometer for Electric Scooter Electric Bike Modification

View on Amazon

Best for: Budget display replacement

A straightforward meter for riders who want speed and odometer readouts across 24V, 36V and 48V systems.

Pros

  • Covers three common voltage levels
  • Shows speed and odometer on one screen

Cons

  • Some owners report the wiring diagram needs careful matching

View on Amazon

Buying Guide

Match the voltage

Most e-bike batteries run at 24V, 36V, 48V or higher, and a display or controller must match that system. Check the battery label before buying any electrical part.

Confirm the connector type

Count the pins and compare the plug shape with your existing harness. Many mismatches come from a connector that looks similar but has a different pin layout.

Measure cable length

Measure the distance between the part and the controller, then add a few centimeters for routing. A cable that is too short causes strain on the connector.

Choose mechanical or electronic brakes

Mechanical levers pull a cable, while electronic levers send a signal to cut motor power. Make sure the lever type matches your brake system.

Good picks for this: 2-Wire Electronic Brake Lever Pair and LCD 5-Pin Electric Bike Display

FAQ

Can I replace an e-bike display myself?

Yes, if the battery is disconnected and the connector matches your controller. If you are unsure about wiring, consult a qualified bike mechanic.

Do brake levers need to be matched to the motor controller?

Electronic levers usually need to match the signal type your controller expects. Mechanical levers do not connect to the controller at all.

Why use an extension cable instead of a new harness?

An extension cable is a quick fix when a single wire is slightly short. A full harness replacement is cleaner if several wires are damaged.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our cycling for beginners guides, checking product details against manufacturer specifications and owner feedback.