Updated November 2026

A bike tube size conversion chart lets you translate the same tire size written three different ways: inches, ETRTO and millimeters. Once you can read all three, you can buy a replacement inner tube that fits your tire without guessing. This guide shows you how to read each system, convert between them, and confirm your match before you buy.

Why Tire Sizes Come in Three Formats

Bike tire sizes are written in several systems because different countries and manufacturers adopted different standards. Inch sizes such as 26 x 1.95 or 700 x 25c are common on older and road bikes. The ETRTO (European Tyre and Rim Technical Organisation) system uses two millimeter figures, like 54-559, and is the most precise. Some tubes and tires also list a plain millimeter width, such as 47 mm. A conversion chart matches these numbers so you are comparing like with like.

Shopping for one? See our guide: 5 Best Road Bike Shoe Size Charts (2026): Expert Picks.

How to Convert Between Inches, ETRTO and Mm

Start with the size printed on the tire sidewall, then find the matching row in the chart. Use the ETRTO number whenever you can, because it describes both the tire width and the wheel diameter in millimeters, which removes most of the ambiguity.

  1. Read the size on the tire sidewall. Look for the two numbers in an ETRTO format, such as 37-622.
  2. If the sidewall shows only inches, such as 26 x 1.95, find that exact entry in the chart and note the ETRTO equivalent beside it.
  3. Confirm the wheel diameter. The second ETRTO number (622 in the example) is the bead seat diameter, which must match your rim.
  4. Check the tube’s valve type and the tube’s stated size range. Choose a tube that lists your ETRTO number within its range.
  5. Compare the result with the mm width printed on the tube box to confirm you have the right width.

Common Conversions at a Glance

The table below shows typical matches. Always verify against your own tire, since some brands label sizes slightly differently.

Inch size ETRTO Approx. width (mm)
26 x 1.95 50-559 about 50
27.5 x 2.1 54-584 about 54
700 x 25c 25-622 about 25
700 x 32c 32-622 about 32

Checking Your Match Before You Buy

Measure the actual tire rather than relying only on the label. Remove the wheel, press the tire bead off the rim, and read the sidewall in the bead area where the lettering is easiest to see. Some older tires wear the numbers off, so a tape measure across the tire width at its widest point can help confirm the width. Manufacturers specify tube ranges on the packaging, and owners often report that the tube fits best when the tire is within the middle of that range.

A set of tire levers makes it easier to remove a tire and fit a new tube without pinching it. View on Amazon

A hand pump or floor pump with a gauge lets you inflate the new tube to the pressure printed on the tire sidewall. View on Amazon

Tips and Common Mistakes

  • Do not match on inches alone. Two tires labeled 700c can differ in width, so check the mm or ETRTO width.
  • Choose a tube whose valve length suits your rim depth. Deep-section rims need longer valves.
  • Avoid stretching a tube that is too small. It can overheat, thin out and fail early.
  • Keep a spare tube in your saddle bag sized to your primary wheel, not a different one.
  • If you are unsure about a fit, ask a local bike shop to check your tire size before you ride.

For more detail on specific bike types, see Bike Tube Size Chart: How to Match Your Inner Tube in 5 Steps and Bike Tire Size Conversion Chart: Match ETRTO, Inches and Mm. If you ride road bikes, Road Bike Tire Tube Size Chart: How to Match Your Tube in 5 Steps covers the narrower formats in more depth.

FAQ

Is ETRTO more accurate than inches?

Yes. ETRTO gives the tire width and bead seat diameter in millimeters, which avoids the confusion that arises when two different inch sizes describe nearly identical tires.

Can I use a tube that is slightly wider than my tire?

A slightly wider tube is usually acceptable if it stays within the tire’s listed range, but a tube that is too large will fold and pinch. Stick to the range printed on the box.

Do I need to measure my tire if the sidewall is worn?

If the printing is hard to read, measure the tire width with a tape and check the wheel diameter against your rim. A local bike shop can also confirm the size for you.

Conclusion

A bike tube size conversion chart turns three confusing formats into one clear answer. Read the tire size in ETRTO when you can, convert inch sizes using the chart, and confirm the width on the tube packaging. Taking two minutes to check the match now saves a roadside repair later.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our cycling for beginners guides, checking product details against manufacturer specifications and owner feedback.